Pete's Grant No.9

Forum for discussion relating to the M3 Lee nd Grant Medium Tank
Pete Nash
Posts: 246
Joined: Sat Oct 01, 2016 10:11 am
Location: Near Ipswich, suffolk
Has liked: 312 times
Been Liked: 90 times

Re: Pete's Grant No.9

Post by Pete Nash » Tue Apr 16, 2019 3:33 pm

Thanks, I smoothed off the wrong places.

Pete Nash
Posts: 246
Joined: Sat Oct 01, 2016 10:11 am
Location: Near Ipswich, suffolk
Has liked: 312 times
Been Liked: 90 times

Re: Pete's Grant No.9

Post by Pete Nash » Thu May 02, 2019 6:52 pm

t a lot of work done recently, the dreaded garden needed attention.
Had to do a 'fix' on a tool so needed some worktop space so piled everything onto the hull.

It's going to be a BEAST!!! :) :) :shock: :shock:

Don't take too much notice of the slack tracks they are only on there to save workshop space. Still plenty of work to do. 8) :( :|
Attachments
DSC_0089.JPG

Pete Nash
Posts: 246
Joined: Sat Oct 01, 2016 10:11 am
Location: Near Ipswich, suffolk
Has liked: 312 times
Been Liked: 90 times

Re: Pete's Grant No.9

Post by Pete Nash » Fri May 03, 2019 12:59 pm

Good and bad news!

The good news is from Monique that she has started to ship the Grant Accessory packs.

The bad news is that I'm going to have to strip down my tracks and get them painted and re-built with lock-nuts sooner rather then later...

Roll on rainy days when I can't get outside to cut grass and the hoovering can wait :D :P :roll:

Pete Nash
Posts: 246
Joined: Sat Oct 01, 2016 10:11 am
Location: Near Ipswich, suffolk
Has liked: 312 times
Been Liked: 90 times

Re: Pete's Grant No.9

Post by Pete Nash » Thu May 09, 2019 5:31 pm

The Option Packs duly arrived on Tuesday (thanks Monique and UPS)>
The S H One T weather has promted me to go back to the running gear ready for fittion the Motion Pack.

Phase 1. Remove the road wheels and carry out the 'Adrian Harris Mods'; Fill in the recesses on the Suspension Arms ( ED01120 and then round off the ends.

Removing the Road Wheels wasn't as hard as it looks.

First I centre popped the axle, drilled M2.5 and tapped M3
Found a long M bolt, gripped it with mole-grips and bashed the mole grips with a hammer. It was a bit tight to start but when the axle came out of the inboard recess of the Bogie Frame EN0104.

I have a lousy sense of where the centre is so I Intend to put the axle in the lathe and drill new holes to represent those on the actual axles.

Adrian Used P38 to fill his Suspension Arms, I'm using Chemical metal as I already have it. (Other fillers are available :roll: ).
Attachments
DSC_0090.JPG

Pete Nash
Posts: 246
Joined: Sat Oct 01, 2016 10:11 am
Location: Near Ipswich, suffolk
Has liked: 312 times
Been Liked: 90 times

Re: Pete's Grant No.9

Post by Pete Nash » Tue May 14, 2019 7:16 am

Adrian Harris visited Bovy recently and sent me this image of the Wheel Axle. It shows a number of details.

1. The hole in the middle is about 21mm 7/8 inch across.
2. The 'nu' on the end is quite thin.
3. the end of the Arm has a pronounced 'Round' to it.

Here is what I have done to replicate it.
1. I bought some M8 Form B washers.
2. I bought some M6 half nuts.
Put the nuts on the axle and into the lathe chuck.
3. machined the excess Axle off
4. Then machined it all down until the half nut was 2mm thick.
5. Drilled an M3 hole in the axle end.

The Axle hole should be 3.5 mm at 1/6 scale but I was too scared to weaken the axle.
The M8 washer is slightly oversize but some filler should blend it in.
The inside end of the axle is being left as supplied as it is not visible.
Attachments
DSC_0094.JPG
Adrian' wheel.jpg
Adrians Image taken at Bovy

Post Reply